Description
Cisco 2010 Connected Grid Router
The Cisco CGR 2010 Connected Grid Router is a rugged, purpose-built network device engineered for the demanding environments of transmission and distribution substations. It combines industrial-grade hardware with Cisco's trusted software capabilities to deliver secure, reliable communications across substation networks. Designed to support critical grid operations, it enables protection and control systems, SCADA data flows, and remote management while withstanding the harsh conditions typical of power facilities. Whether deployed at a substation edge or as part of a centralized grid management topology, the CGR 2010 is built to ensure steady connectivity, resilient performance, and simplified integration with the broader Cisco Connected Grid architecture. By consolidating multiple interfaces, robust security features, and strong lifecycle support, this router helps utilities optimize reliability, reduce downtime, and accelerate deployment of smart grid initiatives.
- Rugged, substation-grade design tailored for harsh environments and wide operating conditions, keeping critical communications online where it matters most.
- Flexible connectivity with multiple Ethernet interfaces and serial ports to bridge legacy devices and modern automation equipment.
- Integrated security features including firewall capabilities, encrypted remote access, and VPN support to protect critical grid communications.
- Optimized for low-latency, reliable transport of control and monitoring traffic, with quality of service and traffic prioritization for essential substation data.
- Remote management and lifecycle support that simplifies firmware updates, monitoring, and centralized configuration across distributed substations.
Technical Details of Cisco 2010 Connected Grid Router
- Specifications: Get this information from the product specifications section on the supplier’s listing; exact figures (UPC/SKU) are required to retrieve complete technical details from ec.synnex.com. If not provided in the current description, consult the official spec sheet or catalog entry for precise hardware, interface counts, and supported protocols.
How to install Cisco 2010 Connected Grid Router
Installing the CGR 2010 to support substation communications begins with careful planning and proper site preparation. Begin by defining your substation topology, including where the CGR 2010 will reside, which devices will connect, and how remote management will be achieved. Confirm power availability, grounding requirements, and ventilation in the equipment enclosure. Establish a baseline security configuration and determine which interfaces will carry control, telemetry, and management traffic. By aligning installation with your utility’s network design and security policies, you can minimize integration time and improve overall reliability.
- Pre-installation planning: Map the substation network layout, identify devices to connect (SCADA terminals, RTUs, sensors), and verify power availability and grounding provisions. Prepare a security baseline and ensure firmware and configuration backups before any change.
- Physical installation: Mount the CGR 2010 in a suitable enclosure or rack, ensuring proper ventilation, ingress protection as applicable, and secure cable management. Route power and network cables to minimize interference and maintain clear separation between critical and non-critical networks.
- Power provisioning: Connect to a stable power source with appropriate protection (surge suppression and grounding). If supported, configure any redundant or hot-swappable power options to maximize uptime in case of power disturbances.
- Network configuration: Access the device through its management interface, assign IP addresses to each interface, and configure core services such as routing, firewall rules, and VPN settings. Apply QoS policies to guarantee priority for protection and control traffic and set up secure remote access for ongoing maintenance.
- Validation and commissioning: After configuration, verify connectivity to all connected devices, test failover scenarios, and monitor link health. Run end-to-end tests to confirm that telemetry data, control commands, and management traffic traverse as intended, and document the final configuration for future audits.
Frequently asked questions
- Q: What is the primary purpose of the Cisco CGR 2010? A: It is a rugged connected-grid router designed to provide secure, reliable communications for substation networks, enabling protection, control, monitoring, and remote management within smart grid deployments.
- Q: Which interfaces does the CGR 2010 offer? A: The router provides multiple Ethernet interfaces and serial connections to bridge modern automation equipment with legacy devices, supporting flexible network architectures in substations.
- Q: Does the CGR 2010 include security features? A: Yes, it includes firewall and VPN capabilities to protect critical grid communications and to enable secure remote management of substation devices.
- Q: Can the CGR 2010 operate in tough substation environments? A: It is purpose-built for industrial settings, delivering a rugged, reliable platform designed to withstand the challenges of field deployments in transmission and distribution facilities.
- Q: How do I obtain the official technical specifications? A: The precise specifications are listed in the supplier’s product page or catalog. For this listing, you should reference the UPC or SKU to access the full spec sheet on ec.synnex.com or the vendor’s engineering documentation.
Customer reviews
Showing - Of Reviews