Intel Compatible E10GSFPT: TAA Compliant, Functionally Identical 1G/10GBASE-T Copper SFP+ for Cat6A/Cat7 RJ-45

Discover the power and versatility of the Intel Compatible E10GSFPT SFP+ transceiver. Engineered to deliver seamless compatibility with Intel-based servers and a wide range of network switches, this TAA-compliant, functionally identical copper SFP+ module enables high-speed 1G/10GBASE-T connectivity over standard RJ-45 copper cabling. Designed for reliability and easy integration, it comes pre-programmed, tested, and supported in the USA, backed by a lifetime warranty for total peace of mind. If you’re upgrading data center fabric, edge deployments, or campus networks, this SFP+ module unlocks up to 10 Gbps on copper while maintaining backward compatibility with 1 Gbps networks and legacy hardware.

• High-performance 1G/10GBASE-T copper SFP+ — Build flexible, cost-efficient networks that can scale from 1 Gbps to 10 Gbps. This module supports both 1GBASE-T and 10GBASE-T, allowing seamless upgrades without replacing existing copper infrastructure.
• Intel compatibility and TAA compliance — Specifically engineered to be functionally identical to Intel’s E10GSFPT, ensuring reliable operation in Intel-based servers and networking equipment. TAA compliance makes it a smart choice for government and enterprise buyers seeking federal procurement-ready hardware.
• RJ-45 copper with Cat6A/Cat7 support — Connect to standard RJ-45 copper cabling, optimized for Cat6A and Cat7 runs. The transceiver maintains robust performance over copper while eliminating the need for fiber components in many data center and office deployments.
• Plug-in, programmable, and tested in the USA — Each unit ships programmed for quick deployment, tested for reliability, and supported domestically. The module is designed for straightforward installation with minimal downtime and maximum compatibility with your existing SFP+ slots.
• Lifetime warranty and trusted support — Invest with confidence: a lifetime warranty backs the product, alongside access to knowledgeable US-based support for setup, diagnostics, and troubleshooting.

Technical Details of Intel Compatible E10GSFPT

• Interface: SFP+ copper transceiver module for 10GBASE-T with RJ-45 compatibility
• Supported speeds: 1GBASE-T and 10GBASE-T
• Cable type: Cat6A or Cat7 copper Ethernet cabling via RJ-45
• Maximum link distance: Up to 30 meters on appropriate Cat6A/Cat7 cabling
• Compliance: TAA compliant; Intel-compatible (functionally identical to E10GSFPT); tested and programmed in the USA
• Form factor: SFP+ transceiver module
• Warranty: Lifetime warranty

how to install Intel Compatible E10GSFPT

Installing the Intel Compatible E10GSFPT is straightforward and designed to minimize downtime. Follow these steps to ensure a successful deployment in servers, switches, or routers that support SFP+ copper modules:

1) Verify compatibility — Confirm that your network device supports 10GBASE-T SFP+ modules and that the device’s firmware is up to date. Ensure the hardware can operate with copper SFP+ modules using RJ-45 ports.

2) Power down (for critical installations) — If your deployment policy requires it, power down the device before inserting or removing SFP+ modules. In many cases, hot-swapping is supported, but following your equipment’s best practices reduces risk.

3) Insert the SFP+ module — Carefully align the module with the SFP+ slot and slide it in until it clicks into place. Avoid excessive force; the module should sit firmly with the contact pins fully engaged.

4) Connect the copper link — Attach a Cat6A or Cat7 Ethernet cable with RJ-45 connectors to the transceiver and the corresponding network device. Ensure the cable’s category and length comply with your network design requirements (up to 30 meters for optimal 10G throughput).

5) Verify link status and speed — Power up the equipment (if powered down) and check the device’s port status. Confirm the link is established at the desired speed (1G or 10G). If needed, configure speed/duplex settings on the switch or NIC to achieve stable operation.

6) Monitor performance — Run basic connectivity tests, latency checks, and throughput measurements to ensure the link meets your performance targets. If issues arise, review cable quality, category compliance, and firmware compatibility before requesting support.

7) Optional optimization — For environments requiring consistent 10G throughput, consider network design adjustments such as link aggregation, priority queuing, or QoS policies to maximize the copper SFP+ performance while maintaining compatibility with legacy 1G links.

Frequently asked questions

Q: What networks does this SFP+ work with? A: It is designed for Intel-compatible environments and supports both 1GBASE-T and 10GBASE-T over Cat6A/Cat7 copper cables. It is suitable for data centers, enterprise networks, campus deployments, and edge devices that require copper-based 10G connectivity.

Q: What is the maximum copper distance? A: The module supports up to 30 meters on Cat6A or Cat7 copper cabling, which is typical for 10GBASE-T copper deployments. If longer distances are needed, fiber-based solutions may be required.

Q: Is this a drop-in replacement for Intel SFP+ modules? A: Yes. The product is programmed, tested, and supported in the USA and is designed to be functionally identical to the Intel E10GSFPT, ensuring reliable compatibility with Intel-based servers and a wide range of network equipment that supports SFP+ copper modules.

Q: Does it come with a warranty? A: It carries a lifetime warranty, reflecting confidence in its long-term reliability and your continued satisfaction.

Q: Do I need special cables or adapters? A: You should use Cat6A or Cat7 RJ-45 cables designed for 10GBASE-T. Avoid substandard or damaged cables, which can degrade performance. No special adapters are required beyond the standard RJ-45 interface.

Q: Can I use it in a non-Intel environment? A: While primarily designed for Intel-compatible systems, the module is a functionally identical 10GBASE-T copper SFP+ and should operate in other vendors’ SFP+ slots that support copper 10GBASE-T, provided firmware and hardware compatibility checks are satisfied.