Tripp Lite by Eaton SmartRack Wall-Mount Roof Fan Kit - Dual 230V High-Performance Fans, 210 CFM, 3 ft. Cord, C14 Input

The Tripp Lite by Eaton SmartRack Wall-Mount Roof Fan Kit is purpose-built to optimize cooling in wall-mount rack enclosures and server cabinets. Engineered for reliability in demanding data-center environments, this dual-fan kit delivers robust airflow to move heat away from critical equipment, helping to preserve performance and extend the life of your IT infrastructure. With a 210 CFM airflow rating and a versatile 230V dual-fan design, it provides effective, continuous cooling where space is at a premium, making it an ideal upgrade for SmartRack deployments that require improved ventilation without adding clutter or excessive footprint.

• Dual 230V high-performance fans deliver up to 210 CFM of airflow to move heat away from servers, switches, and other heat-generating components inside rack enclosures.
• Specifically designed for SmartRack wall-mount configurations, this roof fan kit fits neatly atop compatible wall-mounted enclosures and server cabinets to maximize airflow within restricted spaces.
• Includes a 3 ft (0.91 m) power cord with an IEC C14 input, enabling straightforward integration with standard data-center power distribution and making it easier to connect to your existing electrical setup.
• Helps reduce hot spots and promote consistent temperatures throughout the enclosure, contributing to improved equipment reliability, reduced thermal throttling, and enhanced uptime for critical IT workloads.
• Built for durability in demanding environments, combining rugged construction with simple maintenance design, so you can rely on steady cooling performance over years of service in a busy data center or office server room.

Technial Details of Tripp Lite by Eaton SmartRack Wall-Mount Roof Fan Kit

• Airflow: 210 CFM
• Voltage: Dual 230V operation
• Cord length: 3 ft (0.91 m)
• Power connector: IEC C14 input
• Mounting: Wall-mount roof fan kit designed for SmartRack enclosures and server cabinets

how to install Tripp Lite by Eaton SmartRack Wall-Mount Roof Fan Kit

Install this fan kit by following careful, methodical steps to ensure proper airflow and safe operation. Before beginning, power down and unplug all equipment inside the enclosure to prevent any electrical hazards. Have the appropriate mounting hardware ready for your specific SmartRack model and wall-mount enclosure configuration. If you are replacing an existing roof panel, remove it following your enclosure’s service instructions and set it aside for now.

1) Identify the optimal position on the top of the wall-mount enclosure to maximize exhaust airflow without obstructing cable management or accessories. Align the mounting points on the fan kit with the pre-drilled holes or mounting interface provided by your enclosure.

2) Attach the fan kit securely to the roof or top surface using the manufacturer-recommended screws or hardware. Ensure the assembly is level and firmly anchored to prevent vibration during operation.

3) Route the 3 ft power cord from the fan kit to a suitable power source within your data-center rack or cabinet, keeping the cord away from hot components and moving parts. Connect the cord to a 230V power supply via the IEC C14 inlet on the fan kit, following your site’s electrical safety practices.

4) Reinstall any roof panel or access cover that was removed during installation. Confirm that there is no interference with cabling, cooling paths, or other accessories inside the enclosure.

5) Power on the enclosure and verify that both fans operate smoothly. Check for proper airflow direction, ensuring that air is drawn through the enclosure to carry heat away from IT equipment. If available, observe temperature readings near critical devices to confirm the cooling improvement.

6) Conduct a brief functional test under typical load conditions. Monitor for unusual vibrations, noise, or vibrations, and address any mounting or alignment issues if they arise. Regularly inspect the fan kit as part of routine data-center maintenance to ensure continued reliability.

Frequently asked questions

• What amperage and voltage does this fan kit require? The kit is designed for dual 230V operation, providing robust cooling for wall-mount SmartRack enclosures while aligning with common 230V data-center power distributions.
• What is the airflow capability of the fans? The dual high-performance fans deliver up to 210 CFM of airflow to move heat away from critical equipment inside the rack enclosure.
• What is the cord length and power connector? The kit includes a 3 ft (0.91 m) power cord and uses an IEC C14 input connector for straightforward connection to compatible power sources.
• Is this compatible with all SmartRack wall-mount enclosures? The fan kit is specifically designed for SmartRack wall-mount configurations and is intended to enhance ventilation within compatible server cabinets and wall-mounted racks.
• How does this improve server reliability? By mitigating hot spots and promoting more uniform temperatures inside the enclosure, the kit helps reduce thermal throttling and supports consistent performance of servers, switches, and other equipment.